If you take the performative aspect of DJing seriously, then the Numark Scratch 2-Channel Scratch Mixer for Serato DJ Pro is the mixer for you. Providing you with everything you need to take your sets to the next level including software-based effects, two types of crossfading, a great sounding filter for each channel, and of course, eight responsive performance pads.
Easy to set up for your DVS system, the bundled software license for Serato DJ Pro with DVS means you’re good to go sooner than you’d think. Simply plug in and get mixing. The booth awaits.
Top class performance. No matter where you play, from underground clubs to the main stage, the DJ mixer is your key to keeping the crowd moving. The 24-bit two-channel mixer fuses incredible hardware with the effortless Serato Pro software. Giving you amazing sound quality, top-notch features, and great software-based effects.
The tough construction means the Scratch Mixer is ready for the tour. And with superb features like the InnoFADER crossfader, you’ll be thankful it can withstand the toughest schedules. There are performance pads – eight in total, an instant loop encoder, and toggle paddles for effects. It’s easy to use, sounds great, and best of all, helps you keep the party going.
Next-gen software. Through the included Serato Pro license, you get all the amazing software features that help you express yourself through your decks. The simplicity of the software means you can concentrate on what matters most – mixing. There are six buttons that allow you to control a comprehensive array of effects, each with editable parameters. The toggle paddles allow you to quickly apply effects before drops or other parts of the song, allowing for total expression from behind the decks.
Looping made easy. Simply push the instant loop encoder down and you can easily loop sections of your song. These are set to your default parameters in your software. Just turn the knob to the right and keep the beat longer or turn it to the left to tighten it up and shorten the length. This is really handy for mixing as you can keep a section going whilst you mix in the new song and vice versa.
Ready for your setup. Even if you already have loads of gear in your performance setup, the Scratch Mixer features all the connections you need. Meaning you can quickly plug in your current gear. Your Scratch Mixer fits in with your gear incredibly easy, acting as a great center point and interface between your turntables, CDJ units, and laptop.
Features:
– Serato DJ Pro with DVS License Included
– Ready to connect to Serato NoiseMap Control Vinyl or CDs (available separately)
– InnoFADER scratch crossfader with reverse and slope control
– (6) direct access effect selectors with dual paddle launch triggers and Dry/Wet FX Control
– (8) performance pads to access hot cues, rolls, and samples
– Filter knobs to create audio sweeps
– Dedicated instant looping knobs
– Separate booth/zone output
– Prime Loop Sound Pack included ($200 value)
– SoundSwitch lighting control software 2-month subscription included
Specifications:
Master Outputs (balanced XLR):
– Frequency Response: 20Hz – 20kHz (+0.2dB)
– Signal-to-Noise Ratio: 108dB (A-weighted max output)
– THD+N: 0.007 (1kHz -1dBFS)
– Maximum Output Level: +20dBu
– Output Impedance: 300Ω
Master and Booth Outputs (RCA):
– Frequency Response: 20Hz – 20kHz (+0.2dB)
– Signal-to-Noise Ratio: 107dB (A-weighted max output)
– THD+N: 0.005 (1kHz -1dBFS)
– Maximum Output Level: +6dBV (2Vrms)
– Output Impedance: 300Ω
Headphone Outputs (1/4” and 1/8” TRS):
– Frequency Response: 20Hz – 20kHz (+0.2dB)
– Signal-to-Noise Ratio: 108dB (A-weighted max output unloaded)
– THD+N: 0.005 (1kHz 10mW per channel into 32)
– Maximum Output Level: +14dBu (unloaded)
– Power Output: 115mW RMS (per channel into 32Ω)
– Output Impedance: 32Ω
Line Inputs (RCA):
– Frequency Response: 20Hz – 20kHz (+0.3dB)
– Signal-to-Noise Ratio: 102dB (A-weighted max input level)
– THD+N: 0.008 (1kHz +6.8dBV -1dBFS)
– Max Input Level: +7.8dBV (2.45Vrms)
– Input Impedance: 47kΩ
Phono Inputs (RCA):
– Frequency Response: RIAA Curve
– Signal-to-Noise Ratio: 99dB (A-weighted max input level)
– THD+N: 0.01 (1kHz -3dB input)
Other Specifications:
– USB: USB 2.0 High-Speed
– ADC / DAC: 24-bit 48kHz
– DSP: 32-bit fixed point
– Drivers: PC: ASIO and Windows Audio / Mac: UAC2 Class Compliant (no add’l driver needed)
– Power Input Typical: 120VAC / 240VAC / 50Hz / 60Hz Auto-Switching
