The Markbass Nano Mark II Bass Amp Head is a compact and lightweight bass head that still holds an incredibly warm natural tone. A new bi-band limiter responds faster and more dynamically to your playing allowing you to add nuances to your booming bass. An updated four-band EQ offers effective controls to easily personalise your sound either boosting or cutting up to 16dB for all four bands. This is partnered with a footswitch input option which allows you to edit your tone at the flick of a switch (pun intended) offering up those scooped bass tones for that perfect percussive snap. Volume isnt an issue with this bass head. A master control knob offers precise control of the level sent out to speaker a pre/post EQ switch means you can route your XLR output before or after the EQ as required. Packing an earth shattering 300W rms at four ohms or 150W rms at eight the Nano Mark II sounds anything but small.
Unlimited tone Blow the room away. With 300W of power at 4 ohms and 150W at 8 this amp will blast your basslines out at incredible force offering more volume than you would ever need. What makes it even better is this earthquake of sound doesn’t come at the detriment of the amp’s tone. The Little Mark IV still holds its iconic natural warmth and provides multiple ways to refine every little detail. A four band EQ is a perfect place to start giving you plenty of room to adjust with the ability to either increase or decrease each band up to 16dB making the head easily customisable to suit any genre. A newly designed bi-band limiter offers a faster response and more dynamic sensitivity to your performance allowing your notes to breathe and generating a more natural sound. No connectivity difficulty Optimised so you can efficiently connect your devices the Nano Mark II offers up a wide selection of connectivity options. An effects loop is situated on the back of the amp head meaning that you can send the tonal influence of the amp to your effects as opposed to just the raw signal of your bass giving you more tonal variation. As you would expect a standard unbalanced 1/4 “ jack input is featured on the front alongside a combo speaker output which is featured on the back alongside a standard DI line out. A footswitch option also allows for quick and efficient EQ scoops for that scintillating slap tone. Gig Ready The Markbass Nano Mark II is the perfect companion for the gigging bassist. Designed to be portable this bass head weighs in at just 1.45kg making it extremely lightweight especially when considering the power it possesses. Built in house from the ground up the bass head comes packed with a power amp crafted to elevate the inherent tone of your instrument ensuring an exceptional live tone so you can perform without limitations. Specifications Input Impedance: 1 Mohm Max. Voltage: 15 Vpp Return Impedance: 33 Kohm Max. Voltage: 10 Vpp Gain:-60 Db To +23 Db Range Pre/Post Eq (For Line Out) Switch: On Rear Panel Ground Lift Switch: On Rear Panel Volume Controls: Mute Switch Master Volume Low: Center Frequency 68 Hz; Level: ±16 Db Mid Low: Center Frequency 360 Hz; Level: ±16 Db Mid High: Center Frequency 800 Hz; Level: ±16 Db High: Center Frequency 5 Khz; Level: ±16 Db Send Effects: Unbalanced Max. Voltage 20 Vpp Line Out: Balanced Xlr Max. Voltage 10 Vpp Speaker Out: Speakon/1/4” Combo 1/4”* Height: 2.09 In. / 5.3cm Width: 7.87In. / 20Cm Depth: 8.27 In. / 21Cm Weight: 3.2 Lbs / 1.45 Kg Limiter: Bi-Band Limiter Footswitch (Optional): Flat/Scooped-Mid Output Power: 300w Rms @ 4 Ohm 150w Rms @ 8 Ohm Power Requirement: 100/120V; 230V; 240V 50/60Hz (Voltage is factory preset according to region of sale)
CHECK PRICES AT ZZOUNDS
