Four processors add up to one superb channel strip. The dbx 286s Microphone Preamp & Channel Strip Processor is a complete solution for getting great sound. Youll get crystal clear sound and the control to adapt to any recording application. Make your sound a cut above the rest. Whatever the sound source take advantage of a compressor de-esser enhancer and expander/gate to perfect your sound. 48V phantom power and an 80 Hz cut off high pass filter ensure you can get a signal from any mic and eliminate low frequency hum or wind noise.
Transparent or apparent – the choice is yours From subtle transparent tweaks to radical sound overhauls you can get the effect you need with the dbx 286s. The compressor can have a high ratio or be used in patented OverEasy® mode. From light acoustic tracks to full on rock performances the 286s has you covered. The de-esser tackles vocal sibilance but you can also use it to remove the harshness or prevent high frequency distortion on other instruments like cymbals or guitars. High and low frequency enhancement are also just an adjustment away. Add some high end sparkle or low end fullness with the turn of a knob. Stay in the loop Precise LED monitoring means youll always be aware of the state of the important settings on your channel strip. LEDs show you the preamp level gain reduction on the compressor as well as info on the de-esser expander and a clipping indicator. Be totally aware of the state of your channel strip and have total peace of mind at your gigs. Specifications Mic Preamp: Connector: XLR Floating balanced Pin 2 Hot Input Impedance: 4.2kΩ Gain: 0dB to +60dB Phantom Power: +48VDC applied to XLR pins 2 and 3 through 6.81kΩ resistors CMRR: >40dB typically 55dB Max input level: 0.2Vrms Gain = 30dB Equivalent Input Noise (EIN): -125dBu 22Hz-22kHz 150Ω source impedance Input Connectors (line): Floating balanced TIP Hot Input Impedance (line): 10kΩ unbalanced 20kΩ balanced Max Input (line): >+21dBu balanced or unbalanced Input Gain Range (line): -15dB to +45 dB Insert: Connector: 1/4 TRS: Normalled; tip is Send ring is Return Impedance: >5kΩ (ring-return); 100Ω (tip-send) Max Level: >+21dBu; >+20dBm (600Ω load-tip) Noise: Distortion: Output Connectors: 1/4 Balanced/Unbalanced TRS Connectors Output Impedance: 100Ω unbalanced 200Ω balanced Max Output: >+21dBu >+20dBm (600Ω load) Gain Adjustment Range: -30dB to +10dB Noise: Frequency Response: 20Hz to 20kHz +0.5 -0.5dB THD: Compressor: Threshold Range: -40dBu to +20dBu Threshold Characteristic: OverEasy® Ratio: >4:1 For input levels beyond 20dB above threshold Max Compression: 30dB Attack Time: Program-Dependent; >1s for small level increases down to 10ms for larage increases Release Time: Program-Dependent; adjustable between approximately 1dB/sec and 75dB/sec Distortion: Typically IMD SMPTE: De-esser: Characteristic: Wideband Gain Reduction Frequency Range: 800Hz to 10kHz High Pass 12dB/octave Release Time: 12dB/octave Program-Dependent; approximately 1mS/dB Enhancer: HF Detail: Characteristic Program-controlled shelving equalizer approximately 15dB maximum HF boost LF Detail: Characteristic Bell-shaped boost at 80Hz bell-shaped cut at 250Hz ratio is approximately 2:1 Expander/gate: Threshold Range: OFF to +15dBu Ratio Adjustable: 1.5:1 to 10:1 Max Depth: >50dB Attack Time: Program-Dependent approximately 2mS (at maximum attenuation) Release Time: Program-Dependent approxiamtely 10mS/dB Dynamic Range: Typically 105dB Power Consumption: 15W Operating Voltage DO: 120VAC 60Hz 100VAC 50/60Hz; EU: 230VAC 50/60Hz Operating Temperature: 0°C to 45°C Dimensions: 4.5cm x 14.6cm x 48.5cm Unit Weight: 2.04 kgs Shipping Weight: 2.97 kgs Your title here…
CHECK PRICES AT ZZOUNDS
